CHAMBERLAIN Universal Wireless Keypad LIK2U/-P2;KLIK2C/-P2 Manual

  • Post last modified:May 17, 2023
  • Post category:Chamberlain

Chamberlain Logo

CHAMBERLAIN Universal Wireless Keypad LIK2U/-P2;KLIK2C/-P2 Manual

CHAMBERLAIN Universal Wireless Keypad LIK2U-P2;KLIK2C-P2 featured img

MODELS

KLIK2U, KLIK2U-P2, KLIK2C AND KLIK2C-P2

Introduction

Thank you for your purchase of the Universal Wireless Keypad.

PLEASE DO NOT RETURN TO THE RETAIL STORE.

If for any reason you have questions or need help with troubleshooting please call: 1-800-442-1255.

Read instructions thoroughly BEFORE beginning. If using this product with residential door openers, this product must be used only with door openers manufactured after 1993 that utilize photoelectric sensors. The photoelectric sensors are always located on or near the bottom of the door track.

WARNING: This product can expose you to chemicals including lead, which are known to the State of California to cause cancer or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:
• Install keypad within sight of garage door, out of reach of small children at a minimum height of 5 feet (1.5 m) above floors, landings, steps or any other adjacent walking surface, and away from ALL moving parts of door.
• ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote controls.
• Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door.

Programming

DETERMINE GARAGE DOOR OPENER TYPES:

Proceed with instructions according to your garage door opener type. NOTE: Your motor unit and/or remote control may look different.

TYPE 1

Chamberlain, Sears Craftsman, Lift Master, Master Mechanic and Do It garage door openers or receivers with: 3 position DIP switches. CHAMBERLAIN Universal Wireless Keypad LIK2U-P2;KLIK2C-P2 img 1

  1. Select and write a 4-digit PIN: __ __ __ __
  2. Determine your opener ID using the list below. CHAMBERLAIN Universal Wireless Keypad LIK2U-P2;KLIK2C-P2 img 6
  3. The first DIP switch must be set to the “-” position on your remote and opener. Record your DIP switch sequence for remaining DIP switches. If the DIP switch is in the “+” position place a 1, “0” position place a 2, “-” position place a 3 in the corresponding box in the chart below:
    NOTE: Leave any unused switch locations blank. CHAMBERLAIN Universal Wireless Keypad LIK2U-P2;KLIK2C-P2 img 7
  4. Press and hold the * and # buttons until keypad stops flashing. CHAMBERLAIN Universal Wireless Keypad LIK2U-P2;KLIK2C-P2 img 8
  5. Enter PIN from step 1, press #.
  6. Enter ID from step 2, press #.
  7. Enter DIP switch sequence from step 3 and press # key.
    CHAMBERLAIN Universal Wireless Keypad LIK2U-P2;KLIK2C-P2 img 9
  8. To test and use, wait until lights turn off, enter your PIN and press the 0 key. CHAMBERLAIN Universal Wireless Keypad LIK2U-P2;KLIK2C-P2 img 10

If opener does not function, repeat programming.

TYPE 2

Genie, Linear and Moore-OMatic garage door openers or receivers with: 2 position DIP switches. CHAMBERLAIN Universal Wireless Keypad LIK2U-P2;KLIK2C-P2 img 2

  1. Select and write a 4-digit PIN: __ __ __ __
  2. Determine your opener ID using the list below. CHAMBERLAIN Universal Wireless Keypad LIK2U-P2;KLIK2C-P2 img 11
  3. Record your DIP switch sequence. If DIP switch is in the “on” or “up” position place a 1, “off” or “down” position place a 2 in the corresponding box in the chart below: NOTE: Leave any unused switch locations blank. CHAMBERLAIN Universal Wireless Keypad LIK2U-P2;KLIK2C-P2 img 12
  4. Press and hold the * and # buttons until keypad stops flashing. CHAMBERLAIN Universal Wireless Keypad LIK2U-P2;KLIK2C-P2 img 8
  5. Enter PIN from step 1, press #.
  6. Enter ID from step 2, press #.
  7. Enter DIP switch sequence from step 3 and press # key. CHAMBERLAIN Universal Wireless Keypad LIK2U-P2;KLIK2C-P2 img 9
  8. To test and use, wait until lights turn off, enter your PIN and press the 0 key. CHAMBERLAIN Universal Wireless Keypad LIK2U-P2;KLIK2C-P2 img 10

If opener does not function, flip DIP switches, so if a switch is “on” or “up” flip it “off” or “down” in step 3.

TYPE 3

Chamberlain, Sears Craftsman, Lift Master, Master Mechanic and Do It garage door openers or receivers with: Yellow, white or grey Smart/Learn buttons. CHAMBERLAIN Universal Wireless Keypad LIK2U-P2;KLIK2C-P2 img 3

  1. Select and write a 4-digit PIN: __ __ __ __
  2. Your opener ID is 11.
  3. Record your DIP switch sequence. Set your first DIP switch to “-”, your first DIP switch must be set to the “-” position on your remote and opener. If the DIP switch is in the “+” position place a 1, “0” position place a 2, “-” position place a 3 in the corresponding box in the chart below: NOTE: Leave any unused switch locations blank. CHAMBERLAIN Universal Wireless Keypad LIK2U-P2;KLIK2C-P2 img 13
  4. Press and hold the * and # buttons until keypad stops flashing. CHAMBERLAIN Universal Wireless Keypad LIK2U-P2;KLIK2C-P2 img 8
  5. Enter PIN from step 1, press #. CHAMBERLAIN Universal Wireless Keypad LIK2U-P2;KLIK2C-P2 img 9
  6. Enter 11, press #.
  7. Enter DIP switch sequence from step 3, press #.
  8. Press and release the Smart/Learn button on garage door opener.
  9. Enter your 4 digit PIN and press the 0 key.
  10. To test and use, wait until lights turn off, enter your PIN and press the 0 key. CHAMBERLAIN Universal Wireless Keypad LIK2U-P2;KLIK2C-P2 img 10

If opener does not function, repeat programming.

TYPE 4

Chamberlain, Sears Craftsman, Lift Master, Master Mechanic, Do It, Genie Intellicode, Overhead Door, Stanley, Wayne Dalton or Linear garage door openers with: Smart/Learn button. CHAMBERLAIN Universal Wireless Keypad LIK2U-P2;KLIK2C-P2 img 4

  1. Select and write a 4-digit PIN: __ __ __ __
  2. Determine your opener ID using the list below. CHAMBERLAIN Universal Wireless Keypad LIK2U-P2;KLIK2C-P2 img 14
  3. Press and hold the * and # buttons until keypad stops flashing. CHAMBERLAIN Universal Wireless Keypad LIK2U-P2;KLIK2C-P2 img 8
  4. Enter PIN from step 1, press #.
  5. Enter ID from step 2, press #. CHAMBERLAIN Universal Wireless Keypad LIK2U-P2;KLIK2C-P2 img 9
  6. Press and release the Smart/Learn button on garage door opener.
  7. Enter your 4 digit PIN and press the 0 key. NOTE: For Genie and Overhead Door units, press the 0 key twice.
  8. To test and use, wait until lights turn off, enter your PIN and press the 0 key. CHAMBERLAIN Universal Wireless Keypad LIK2U-P2;KLIK2C-P2 img 10

If opener does not function, repeat programming.

TYPE 5

Genie Intellicode 2 garage door openers with: Program/Set button.
BEFORE STARTING: You MUST have a Genie IntelliCode 2 remote control with at least one button already programmed to the opener. CHAMBERLAIN Universal Wireless Keypad LIK2U-P2;KLIK2C-P2 img 5

  1. Select and write a 4-digit PIN: __ __ __ __
  2. Press and hold the * and # buttons until keypad stops flashing. CHAMBERLAIN Universal Wireless Keypad LIK2U-P2;KLIK2C-P2 img 8
  3. Enter PIN from step 1, press #.
  4. Press 5, then press #. CHAMBERLAIN Universal Wireless Keypad LIK2U-P2;KLIK2C-P2 img 9
  5. On the garage door opener, press and hold the Program/Set button until both the long and short LED light up BLUE. CHAMBERLAIN Universal Wireless Keypad LIK2U-P2;KLIK2C-P2 img 15
  6. Release the Program/Set button and only the round LED will be lit in BLUE. CHAMBERLAIN Universal Wireless Keypad LIK2U-P2;KLIK2C-P2 img 16
  7. Press and release the Program/Set button and the long LED will flash PURPLE. CHAMBERLAIN Universal Wireless Keypad LIK2U-P2;KLIK2C-P2 img 17
  8. On the Genie® remote control, press and release the button that is already programmed to the garage door opener. Both LEDs will flash PURPLE. CHAMBERLAIN Universal Wireless Keypad LIK2U-P2;KLIK2C-P2 img 18
  9. On the CLICKER® keypad, enter the PIN from step 1, and press and release the 0 key. Both LEDs on the garage door opener will light up PURPLE. CHAMBERLAIN Universal Wireless Keypad LIK2U-P2;KLIK2C-P2 img 19
  10. On the CLICKER® keypad, press and release 0 again. Both LEDs on the garage door opener will light up BLUE. CHAMBERLAIN Universal Wireless Keypad LIK2U-P2;KLIK2C-P2 img 20
  11. On the CLICKER® keypad, press and release 0 again. This will activate the garage door opener and programming is complete. CHAMBERLAIN Universal Wireless Keypad LIK2U-P2;KLIK2C-P2 img 21
  12. To test and use, wait 30 seconds, then enter your PIN and press the 0 key.

If opener does not function, repeat programming.

Installation

Install out of reach of small children at a minimum height of 5 feet (1.5 m) above floors, landings, steps or any other adjacent walking surface, and away from ALL moving parts of door. Secure keypad to a smooth surface. Mount the keypad out of the path of the moving garage door, but within sight of it (4″ [10 cm] clearance is needed for the cover).

  1. Remove cover.
  2. Remove battery cover to expose mounting holes.
  3. Remove battery and mount keypad using screws provided.
  4. Reassemble.

Changing your 4-digit pin

Enter existing PIN, press *, enter new PIN and press *.
To test and use, enter your new PIN and press the 0 key. CHAMBERLAIN Universal Wireless Keypad LIK2U-P2;KLIK2C-P2 img 22

Battery

Warning: To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.

Replace the 9-Volt battery when keypad light becomes dim or does not light up. Slide cover up, remove battery cover, and replace battery.
Re-programming may be necessary. CHAMBERLAIN Universal Wireless Keypad LIK2U-P2;KLIK2C-P2 img 23

FAQs

Why won’t my keypad work?
• Did the keypad lights come on when you entered your PIN? If the keypad lights do not turn on when you press a button, it indicates that the battery needs to be replaced. Replace with a 9V battery.
• Try reprogramming the keypad to the garage door opener.
• Make sure the keypad is compatible with your garage door opener
(Chamberlain 315 MHz or 390 MHz garage door openers manufactured after January 1, 1993).
• If the solutions above did not work, replace the keypad.
How do I erase my pin?
To clear out the keypad, press and hold the * and the # keys together until the keypad stops flashing. Proceed to reprogram the keyless entry.
Can I program the keypad to a second garage door opener?
The keypad can only activate one garage door opener.
Do I always have to use a 0 after my 4 digit PIN to activate the opener?
After programming the keypad, any fifth number will act as the “enter” button to activate the opener.
Why does the door move after I only press 1 number button?
After operating the garage door with the keypad, the keypad lights will flash for 10 seconds. The keypad remains active during the 10 seconds of flashing; any number will activate the door.
Where is my LEARN button located?
If equipped with a LEARN button, it can either be found on the garage door opener or on an external receiver. To locate the receiver look for an antenna. Some receivers will require a cover be removed to gain access to the switch positions.
Will I have to reprogram the keypad after changing the battery?
The keypad should retain its memory. If the keypad no longer operates the operator, reprogram the keypad to your system.
Where is my LEARN button on my gate?
Most gate operators have a built-in radio receiver or an external receiver. The receiver on a gate opener can usually be found within the cabinet of the operator. To gain access you might require permission if used in a community gate.

WARRANTY

ONE YEAR LIMITED WARRANTY
The Chamberlain Group, Inc. warrants to the first consumer purchaser of this product that it is free from defect in materials and/or workmanship for a period of 1 year from the date of purchase.

NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Tested to Comply with FCC Standards for Home or office use. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Chamberlain Logowww.chamberlain.com
1-800-442-1255

Leave a Reply